using freecad to convert 3d drawing to 2d sketch

USING FREECAD TO CONVERT 3D DRAWING TO 2D SKETCH SERIES
USING FREECAD TO CONVERT 3D DRAWING TO 2D SKETCH DOWNLOAD

… three Mississippi, four Mississippi … and stop the clock, which shows that it took just a few seconds to produce the figure below. Click above the first view, then to the right of the first view, then approximately in the center of the upper-right quadrant of the layout, then press Enter. … two Mississippi …ĪutoCAD continues asking for view locations. Click approximately in the center of the lower-left quadrant of the drawing, then click eXit in the context menu or press Enter. One Mississippi …ĪutoCAD asks for a view location. Having started the ViewBase command, click on From Model Space in the drop-down menu that appears. A couple of paragraphs back, I bragged that I could create the 2D drawing views of our sample part in under a minute. A layout tab has to be current for the Layout tab to show. You’ll find it on the Ribbon menu > Layout tab > Create View panel > Base button. (You can eliminate the need for this step in future drawings by deleting it from your template file.)

USING FREECAD TO CONVERT 3D DRAWING TO 2D SKETCH DOWNLOAD

( You can download it if you want to follow along.)Ĭlick on the Layout 1 tab to make it current.ĭelete the existing viewport. I’ll demonstrate, using the same simple part from the earlier article.

Well, using the ViewBase command I can reproduce that drawing in well under one minute, assuming I have the 3D model to begin with. In my first article about 3D-to-2D, I bragged that I had created four ortho views and an isometric view in under five minutes. (So by delaying this column until now, I have cunningly avoided the need to write one about the SectionPlane family.)

USING FREECAD TO CONVERT 3D DRAWING TO 2D SKETCH SERIES

In due course they produced the SectionPlane family of commands, which made it much easier to produce 2D drawing and cross-section views.Īnd AutoCAD 2012 introduced yet another series of 3D-to-2D commands, which make it almost trivially easy to produce 2D drawing and section views from solid models. Time and the Autodesk programmers marched on. This combination is more powerful and versatile than FlatShot but takes a little more effort, and once again has a few limitations and gnarly bits. Next came the command sequence using the SolView, SolDraw, and SolProf combination, as covered in my second column of this series. It is still the fastest and easiest for producing a quick-and-dirty view but it has too many limitations if you want to get fancy. My first column on this topic covered the FlatShot command, which is the oldest and simplest. AutoCAD in fact has four basic processes for producing 2D drawings from 3D models. Generating 2D working drawings from 3D models!īut haven’t you already covered that in two previous columns?Īctually, those two columns hardly covered the half of it. He loves the freedom to move at will in all three dimensions, as opposed to only two when he's on the surface - that’s it! This month’s topic! Six dives in two days would bring the Captain’s lifetime total to 226. That's one fairly big step for Captain LearnCurve. Suddenly a shout rang out: 'Divers in the water!' With a series of splashes the Captain and his son stepped overboard, along with the divemaster and four other divers. … about 40 miles offshore from Cairns, Australia, just outside the Great Barrier Reef. Wait a minute! You live in Vancouver, Canada! How could you be relaxing on the deck of a boat in December? Captain LearnCurve, his gorgeous wife, and their son and daughter-in-law were relaxing in the sun on the deck of the Silver Spirit … It was a warm and sunny December morning, just before Christmas. Yet Another Way to Go from 3D to 2D in AutoCAD 21 Jan, 2015 By: Bill Fane Learning Curve tutorial: To create 2D views from 3D models quickly, try the ViewBase family of commands.

Using freecad to convert 3d drawing to 2d sketch